2 votes, 5 avg

Civil Engineering Drawing Online Test 1 (Free)

-: Symbols & Description :-

(નિશાનીઓ અને તેનું વર્ણન)

-: Instructions :-

(સૂચનાઓ)

1. Click On Full Screen Mode (¤) From Corner For Best Test Experience

(બેસ્ટ ટેસ્ટ અનુભવ માટે ખૂણામાં આપેલ ફૂલ સ્ક્રીન મોડ (¤) ઉપર ક્લિક કરો)

2. Use Navigation Bar For Jumping Forward or Backward To Any Question

(કોઈ પણ પ્રશ્ન ઉપર જવા માટે નેવિગેશન બારનો ઉપયોગ કરવો)

3. Submit Test Button Will Be Only Visible At The Last Question

(ટેસ્ટ સબમિટ કરવાનો ઓપ્શન માત્ર છેલ્લા પ્રશ્ન ઉપર હશે)

4. Don't Forget To Give Your Rating & Review At The End Of Test

(ટેસ્ટ પૂરી થયા પછી રેટિંગ & રિવ્યુ આપવાનું ભુલશો નહીં)

"BEST OF LUCK"

[Click On Full Screen Mode (¤) From Corner For Best Test Experience]

(બેસ્ટ ટેસ્ટ અનુભવ માટે ખૂણામાં આપેલ ફૂલ સ્ક્રીન મોડ (¤) ઉપર ક્લિક કરો)

---------------

Your Name

1 / 10

Category: Orthographic Projections (Engineering Graphics & Design)

A triangular prism is placed in a projection plane such that the square surface is parallel to the horizontal plane. The top view, front view will be __________.

triangle, rectangle respectively

rectangle, rectangle respectively

rectangle, triangle respectively

square, rectangle respectively

2 / 10

Category: Lettering & Dimensioning (Engineering Graphics & Design)

What is the minimum spacing between words in type A standard of lettering?

(20/14)h

(6/14)h

(2/14)h

(1/14)h

3 / 10

Category: Isometric Projections and Isometric Views (Engineering Graphics & Design)

Isometric view of rhombus will become __________.

square

rectangle

rhombus

parallelogram

4 / 10

Category: Projections of Points (Engineering Graphics & Design)

Projection of a point in the third quadrant will be

Front view in PP

Front view in HP

Front view in VP

None of Above

5 / 10

Category: Building Drawing Symbols (Building Planning And Drawing)

The symbols A and B represent _______ and _______ respectively.

Gauge, alarm

Generator, alarm

Gauge, ammeter

Generator, ammeter

6 / 10

Category: Development of Surfaces (Engineering Graphics & Design)

Approximate development is the method of developing of non-developable surfaces, by divided the surface of the object into __________

Zone and lune

Circular parts

Triangular parts

Parallel parts

7 / 10

Category: Projections of Solids (Engineering Graphics & Design)

The front view, side view and top view of a regular square pyramid standing on a horizontal plane base on the horizontal plane.

triangle, square and triangle

square, triangle and square

square, triangle and triangle

triangle, triangle and square

8 / 10

Category: Building Drawing Symbols (Building Planning And Drawing)

The symbol given below represents __________

Split stair

L-shaped stair

Ornamental stair

Scissor stair

9 / 10

Category: Introduction to Engineering Graphics (SP-46) (Engineering Graphics & Design)

What is the type of scale in which the representative fraction is 1:1?

Graphical scale

Full-size scale

Reduced scale

Enlarged scale

10 / 10

Category: Introduction to Engineering Graphics (SP-46) (Engineering Graphics & Design)

Which of the following grades of leads is the hardest?

Your score is

The average score is 29%

"Rate This Test"

"Thank You"

Leaderboard :

Pos.	Name	Score	Duration
1	abc	50 %	2 minutes 31 seconds
2	HUB	50 %	4 minutes 26 seconds
3	Jatin	50 %	5 minutes
4	vipul dholakiya	40 %	1 minutes 53 seconds
5	Joshi	40 %	3 minutes 20 seconds
6	Makwana Vishalbhai	40 %	3 minutes 27 seconds
7	B.J	40 %	3 minutes 45 seconds
8	Suryadeep	30 %	1 minutes 42 seconds
9	Deep	30 %	3 minutes 33 seconds
10	Rahul Makwana	20 %	1 minutes 48 seconds
11	Yagnika Rathod	20 %	2 minutes 8 seconds
12	Guest	0 %	0 second
13	Ghoghari Jatin	0 %	11 seconds
14	Rupesh Prajapati	0 %	5 minutes

Civil Engineering Drawing Online Test 1 (Free)